Genesis v1.2 Parts

This IP67 rated borescope camera has a custom 1m focal distance. The USB cable comes in both 5m (Genesis) and 6.5m (Genesis XL) lengths.

These magnets keep tools attached to the UTM. Sold in packs of 3. Material: Neodymium (NdFeB) Coating: Nickle (Ni) ...

M5 button-head screws of various lengths are used throughout FarmBot to attach plates and 3D printed parts to extrusions, V-wheels to plates, and o...

These interchangeable needles are used with the FarmBot Seed Injector to pick up seeds and deposit them in the soil. We have three sizes: 16, 19, a...

These NEMA 17 stepper motors come with pre-mounted rotary encoders. They are sold individually, and do not include any wiring harnesses. For a comp...

These O-rings fit onto the UTM's liquid/gas ports and create a solid seal when tools are mounted. Sold in packs of 3. Material: Buna-N...

These brass barbs screw into the UTM's three liquid/gas ports and accept the three liquid/gas lines coming from the z-axis cable carrier. Sold in p...

This adapter allows luer lock needles to be mounted to the seeder base and easily interchanged with a 1/4 turn.

These ultra flexible tubes carry water to the UTM and suck vacuum air. Lengths: 0.4m, 3m, 6m Material: Silicone or PVC Color: Semi Clear o...

These grommets fit onto the UTM cover and allow the liquid/gas tubes and the UTM cable to pass into the UTM assembly while keeping water and dust o...

GT2 timing belts are used along FarmBot's tracks and gantry to allow FarmBot to move in the X and Y directions. They mate with the GT2 Pulleys, and...

The Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight...

This 12V vacuum pump sucks air through the seeder's luer lock needle in order to suction-hold a seed on the needle tip during planting. Compatible...

M3 screws are used throughout FarmBot for mounting motors and other small electronic components on the tools. Diameter: 3mm (M3 size) Lengths: 6mm...

This 12V solenoid valve controls the flow of water from your garden hose to FarmBot's tubing. Compatible with v1.2 and v1.3 kits. Inlet: 3/4" NPT...

The seeder, combined with the vacuum pump, allows FarmBot to pick up seeds and deposit them precisely in the ground. Note: this product does not in...

This delrin block attaches to the cross-slide plate so that the leadscrew can move through it, allowing FarmBot to move in the Z direction. Ma...

These clips secure the ends of GT2 Belts to an aluminum extrusion. Belt clips are sold individually. Six are required for a complete FarmBot. ...

This upgrade kit makes it easy to reposition the vacuum pump to the z-axis, allowing for more powerful suction at the needle. This is for upgrading...

The gantry corner brackets attached the gantry main beam to the gantry columns. They also have mounting holes for the x-axis motors. Note that ther...

The gantry wheel plates hold an array of v-wheels for interfacing with the tracks and have mounting holes for the gantry column. Note that these pl...

This stainless steel leadscrew allows FarmBot to move in the Z direction. Material: Stainless Steel Diameter: 8mm Th...

These components mount on the z-axis extrusion and physically limit how high and low FarmBot can move the z-axis. They are sold individually. Two a...

This tool acts as a mount for the soil sensor circuit board. Material: UV stabilized ABS Color: Gray

These polycarbonate V-wheels are precision machined to allow FarmBot to move in the X, Y, and Z directions smoothly and precisely. Each wheel requi...

These connect the Grounded electronic pin to the Digital In pin, allowing FarmBot to detect when a tool has been mounted or dismounted correctl...

These stainless steel bearings resist corrosion and have rubber seals to keep debris out. Two of them are used in every V-wheel, and one is used to...

Combined with screws, these drop-in style tee nuts allow components such as plates and 3D printed parts to be attached quickly and securely anywher...

These blades are designed to be mounted in various configurations on the weeder tool in order to best work with the types of weeds and soil conditi...

Used to calibrate FarmBot's camera for pixel to coordinate conversion software (used for Weed Detection). Sold in packs of 2. Material...

These springs keep the screws in the UTM in contact with screws in the tools for electrical connections. Sold in packs of 15. Material...

These short wires connect the soil sensor PCB to the M3 electronic screws on the soil sensor base. Sold as a set of three (one of each color) ...

This plug prevents water from entering the UTM cover in the third liquid/gas port. Material: Machined Delrin Color: Black

These pulleys are attached directly to NEMA 17 stepper motor shafts or onto the driveshaft. They transfer power from the motor to the belt such tha...

The weeding tool allows FarmBot to smash weeds into the ground, thereby killing them via mechanical disruption. The tool consists of a base compone...

Track joining plates are used to join two track extrusions end-to-end and attach them both to supporting infrastructure such as a raised bed. Note ...

Track end plates are used to attach the ends of the tracks to supporting infrastructure such as a raised bed. Note: The track end plates are sold i...

These drivers convert step and direction signals from the microcontroller (Farmduino) into powerful electrical pulses sent to the NEMA 17 stepper m...

When rotated, eccentric spacers accurately position V-wheels on a plate such that they can firmly engage V-slot aluminum extrusions. They are only ...

This is the "host computer" of FarmBot. You might also call it FarmBot's brain. The Raspberry Pi runs FarmBot OS, communicates with the web applica...

These spacers are used to offset V-wheels from plates so that they may engage extrusions. Sold in packs of 30. Material: Aluminum ...

The microSD card holds FarmBot OS and is inserted into the Raspberry Pi. Exact packaging may vary. Form Factor: MicroSD Capacity:...

These M5 precision shims are placed in between the two bearings in every V-wheel. They keep the bearings from squishing into each other and binding...