You are not logged in.
- Topics: Active | Unanswered
#51 Re: Bug Reports » Wrong direction movement after print job done. » 2016-04-03 20:18:15
Hi, the shield axis direction is zero at bottom.
#52 Bug Reports » Wrong direction movement after print job done. » 2016-04-03 17:28:13
- color
- Replies: 5
Hello, after the print done I am usually want to go to Z-axis calibration and move the Z axis up to remove the build plate. If I press any button - 1 or 10 or 200mm up, the axis move in opposite direction and the build plate crashes to the vat floor! Nanodlp build 1117
#53 Re: Help and Support » Distro/change button question » 2016-03-29 20:45:20
Thank you for the support, Shahin.
#54 Re: Help and Support » Distro/change button question » 2016-03-29 19:23:33
Yes, this work. Is it necessary to do this every time after reboot or this setting will be remembered?
#55 Help and Support » Distro/change button question » 2016-03-29 18:17:42
- color
- Replies: 4
Hello, It seems the "Change to mUVe3D" button not working. After pressing the button, nothing happened and in setup page I can't see the mUVe default settings. In printer proffile I have "Mcast +sylgard, etc" I have a fresh SD image installed on Rpi3
#56 Re: Help and Support » Problem with installing nanodlp » 2016-03-23 21:39:08
https://www.dropbox.com/s/x2gwbavenkg6b … e.JPG?dl=0
The above are result with unpluged RS232 cable and after connecting to projector. The resolution is in the end.
#57 Re: Help and Support » Problem with installing nanodlp » 2016-03-23 20:55:09
I still have not progress with my projector. I tried these commands - PWR0\r (PWR0)\r in ACSII mode, also in binary. Then I converted these in hexadecimal without\with carriage return at the end but without success. The boud rate is 19200 according Infocus manual. In nanodlp I see /dev/ttyUSB0.
How can I run directly the command to Raspberry via my laptop? Which program to use in Windows7?
About my second issue, I changed the confg. file in sd card and with overscan 65 positive the start window of Raspberry has smaller but the projector image is the same with missing top and right border.
#58 Re: Help and Support » Problem with installing nanodlp » 2016-03-22 18:29:16
Hi again,
Unfortunately the projector control not working for me. I tried both hex and ACSII with PWR1 PWR0 and also converted commands
50 57 52 31 and 50 57 52 30 May be my USB to RS232 is not compatible, but in device manager I see the COM port working.
I have another one question. When I run a calibration image " projector boundaries" I see only left and bottom lines.(see the attached picture) This happened also in CW connected with my desctop PC (NVidia ) But when I connect CW on my laptop Lenovo T60 ( AMD video) the image have the full dimension.
#59 Re: Help and Support » Problem with installing nanodlp » 2016-03-21 09:25:31
Thank you for the help Shahin,
I'll try this later. and will report the result 
#60 Re: Help and Support » Problem with installing nanodlp » 2016-03-21 08:44:34
Hello, can you help me to configure my Infocus projector to be controled via nanodlp. Here are a table with serial commands for IN8606HD but I don't know how to enter this codes to nanodlp.
#61 Re: Help and Support » Problem with installing nanodlp » 2016-03-19 17:14:37
Since I am using a RS232 to USB converter,how to check if it work and how to load its drivers to my pi3?
Too many questions, but this is my first touch to Raspberry.
#62 Re: Help and Support » Problem with installing nanodlp » 2016-03-19 16:46:05
Can you help me with settings to control the projector via RS232 to USB converter. My projector is Infocus IN8606HD, and I know the hex code for turn on and turn off, where should be placed these codes in nanodlp sofware?
#63 Re: Help and Support » Problem with installing nanodlp » 2016-03-19 16:33:38
Thank you very much, it's turned out.
#64 Help and Support » Problem with installing nanodlp » 2016-03-19 15:18:05
- color
- Replies: 15
Hello,
I can not install nanodlp via terminal. Here are the message in the terminal window after my attempt.
(wget http://www.nanodlp.com/nanodlp.muve3d.tar.gz-O-|tar-C /home/pi-xz);cd /home/pi/printer;sudo./setup.sh
bash: tar-C: command not found
--2016-03-19 15:13:49-- http://www.nanodlp.com/nanodlp.muve3d.tar.gz-O-
Resolving www.nanodlp.com (www.nanodlp.com)... 139.162.153.107
Connecting to www.nanodlp.com (www.nanodlp.com)|139.162.153.107|:80... connected.
HTTP request sent, awaiting response... 404 Not Found
2016-03-19 15:13:49 ERROR 404: Not Found.
bash: cd: /home/pi/printer: No such file or directory
bash: sudo./setup.sh: No such file or directory
May be I am typing something wrong, wi fi connection is OK, I am writing my post from this Raspberry. Any help will be appreciated.