Archives: FAQs

If your MINI-Z 4×4 does not go forward or backward while steering control is normal, please tighten the motor-wire screws shown in the pictrue below. If the problem persists after tightening the screws, please try sanding the terminals on the chassis with fine sandpaer carefully not to damage other part.

MINI-Z 4×4 throttle control does not respond while steering is ...

This entry was posted in All Categories Troubleshooting on March 30, 2020 by Takuji Fukumoto

Yes, you can. Please follow the instructions below: EX-2/RR Xpansion Updata V2.12 It’s KO Propo’s website and only mention EX-2/RR, but no worries the firmware is also compatible with EX-6/R Xpansion.

Can I upgrade my EX-6/EX-6R Xpansion to V2.12?

This entry was posted in All Categories on May 21, 2019 by Takuji Fukumoto

If you’ve lost the installation CD or would like to use a newer Windows version that is not officially supported by the 32011, you can get the device driver and software here: DRONE RACER LapCounterBasicSet(Shop ed.) 32031 It is for the Drone Racer Lap Counter but it works with the […]

How can I get the device driver/software for the 32011 ...

This entry was posted in All Categories Troubleshooting on April 1, 2019 by Takuji Fukumoto

You might need to have the ESC of the MINI-Z Buggy VE 2.0 recognize the throttle end point for proper operation. Set the throttle trim to the center and reset all throttle parameters of the transmitter. Turn on the transmitter. Push the throttle trigger to the full brake position and […]

MINI-Z Buggy VE 2.0 Throttle End Point Adjustment

This entry was posted in All Categories Troubleshooting on February 28, 2018 by Takuji Fukumoto

If the gyro does not start to work after powering on the chassis, try putting the chassis on a flat surface for a few seconds. Especially the main board of the MINI-Z RWD and MINI-Z FWD is sensitive and it is strongly recommended to take your hands off the chassis […]

Gyro does not start to work after powering on

This entry was posted in All Categories Troubleshooting on January 5, 2018 by Takuji Fukumoto

If you have set the wrong battery type and the EX-6/EX-6R displays “Battery Alarm Low Voltage” on the screen you can cancel it by pressing “BACK” key and you can set the correct battery type.

How can I get out of the “Battery Alarm Low ...

This entry was posted in All Categories Troubleshooting on December 22, 2017 by Takuji Fukumoto

In order to reset all the parameters of the Perfex transmitter, please follow the steps below:

How can I reset the Perfex KT-18 transmitter?

This entry was posted in All Categories Troubleshooting on December 22, 2017 by Takuji Fukumoto

If the steering cannot be centered within the trim adjustment range, reset the steering neutral position following the steps below: Make sure that the transmitter is powered off. Make sure that the steering trim knob is at the center. Power on the chassis. Set the front wheels to the center […]

How can I reset the neutral position of MINI-Z Sports/RWD/FWD ...

This entry was posted in All Categories Troubleshooting on December 20, 2017 by Takuji Fukumoto

If you hear noise when you fully open the throttle and the MINI-Z VE does not accelerate smoothly, probably the battery is weak and do not supply sufficient power to the brushless motor. Please replace batteries or use fully charged Ni-MH batteries. We strongly recommend that you use Ni-MH batteries […]

My MINI-Z VE does not accelerate smoothly when applying full ...

This entry was posted in All Categories Troubleshooting on December 19, 2017 by Takuji Fukumoto

MINI-Z Info

Kyosho Official MINI-Z Information Site