Shared projects

RAMPS-FD v2 Rev A.1 with selectable EEPROM address

by ildo.
Top
Bottom

2 layer board of 3.96x3.76 inches (100.48x95.40 mm).
Shared on April 2nd, 2015 03:05.

RAMPS-FD v2 Rev A with addition of jumper selectable EEPROM address instead of default 0x50.

Original RAMPS-FD v2 Rev A designed by Bob Cousins

Released under GPLv3
Orignal source code

Order board. Download. Permalink. Embed order link.

Copy this HTML into your page to embed a link to order this shared project

ATX Breakout Board with USB Charging, Rev.B

by ildo.
Top
Bottom

2 layer board of 3.93x3.01 inches (99.90x76.40 mm).
Shared on April 2nd, 2015 02:40.

ATX Breakout Board with dual USB charging capability. ATX 24pin -> 5V, 3.3V, and 12V1; EPS12V (ATX12V 4+4) -> 12V2; PCI-E -> 12V3.

Revision: B. Similar to Rev A except the board size is 99.5mm x 76mm,

USB bottom port is powered by 5VSB, top port powered by regular 5V rail fused to 3A.

This board is based on ATX PSU Distributor from eMAKERshop, and ATX Breakout Board designed by Francesco Truzzi.

BOM

Click on download link below. BOM is in the zip.

Order board. Download. Permalink. Embed order link.

Copy this HTML into your page to embed a link to order this shared project

ATX Breakout Board with USB Charging, Rev.A

by ildo.
Top
Bottom

2 layer board of 4.81x2.17 inches (122.12x55.12 mm).
Shared on March 30th, 2015 00:31.

ATX Breakout Board with dual USB charging capability. ATX 24pin, EPS12V (also known as ATX12V 4+4 for connecting 4 or 8 pin CPU connector), and PCI-E connector can be connected to provide 3 12V “rails” along with 5V and 3.3V outputs.

Revision: A

Top and bottom ground layers are stitched together to allow better heat transfer and reduce noise.

USB bottom port is powered by 5VSB, top port powered by regular 5V rail fused to 3A.

This board is based on ATX PSU Distributor from eMAKERshop, and ATX Breakout Board designed by Francesco Truzzi.

BOM

mouser.com part number provided in parenthesis for reference

  • C1: Capacitor 0.1uF 0805 package (77-VJ0805Y105JXQTBC).
  • D1, D2: LED 0805 package (720-LGR971-KN-1).
  • F1: 3A fuse 1206 package (576-1206L300SLWR).
  • J1: ATX 24 pin, right angle (Sparkfun part).
  • J2: ATX 12v 4+4/EPS12V connector, right angle (538-39-30-0080).
  • J3: PCI-E 12v connector, right angle (538-45558-0003).
  • J4: dual port USB-A (571-1903815-1).
  • P1: Pin header 1x4 (855-M20-9990346).
  • P2: Pin header 1x8 (855-M20-9990846).
  • R1,R2: 1.3k resistor (660-SG73P2ATTD1301F).
  • R3, R4: Power resistors, OPTIONAL. Needed for old ATX power supplies. Use 5-9W power resistors if PSU keeps shutting down.
  • SW1: Power switch (629-GPTS203211B).
  • U1: USB charge port controller (595-TPS2513ADBVR).
  • X1,X3,X5: Terminal block 4P (571-282858-4).
  • X2,X4: Terminal block 2P (571-282858-2).

Optional, X2 & X4 can be combined to use a single terminal block 4P.

For P1, P2 acquiring a single 12pin header and cutting it to length would be cheaper.

Order board. Download. Permalink. Embed order link.

Copy this HTML into your page to embed a link to order this shared project