• Blog
  • Protoneer Shop
  • Projects
    • GRBL Arduino Library
    • Arduino CNC Shield – 100% GRBL Compatible
    • Arduino MORE-CORE Shield – Multi-core Setup
  • Contact Us
Protoneer.co.nz Electronic Prototyping Specialists

Tag Archives: Power Supply

Funky ATX 24-Pin plugs for your PCB projects

2013/03/05 4:00 am / Leave a Comment / Bertus Kruger
ATX-24Pin-Red

On my hunt for some 24-Pin ATX Molex plugs for my PCB designs, I stumbled upon a supplier with a nice range of colors.  Very tempted to finish off my projects with these…

Posted in: Electronics, Power Supply, Uncategorized / Tagged: ATX, Power Supply

Cheap,quick and simple Step-Up / Step-Down Regulator

2013/01/28 7:00 am / Leave a Comment / Bertus Kruger
step-up_step-down_voltage_regulator1

Pololu.com just introduced a tiny new Step-Up / Step-Down voltage regulator. Features Output voltage 2.5 – 8 V Input voltage 2.7 – 11.8 V Output current 500 mA to 1000mA 3 x 11 × 17 mm This will work very well in low-powered devices where you want to every bit of power a battery can offer. It is also … Read More →

Posted in: Electronics, Power Supply / Tagged: Power Supply

Quick 5V Power Supply for Micro-controllers and other devices

2012/12/22 7:18 pm / 1 Comment / Bertus Kruger
LM78XX Circuit

Introduction To run some of my micro-controller projects I needed a constant supply of 5v.   The LM78 series of linear regulators are very useful and comes in a good range of regulated voltages(5, 6, 8, 9, 10, 12, 15, 18, 24). Bill of Materials LM7805 – 5V Linear Voltage Regulator  – Digi-Key – Datasheet 0.33uF Capacitor … Read More →

Posted in: Electronics, Power Supply / Tagged: Power Supply

Top Posts & Pages

  • Arduino CNC Shield - 100% GRBL Compatable
    Arduino CNC Shield - 100% GRBL Compatable
  • Arduino CNC Shield V3.XX – Assembly Guide
    Arduino CNC Shield V3.XX – Assembly Guide
  • Quick GRBL setup guide for Windows (Arduino G-Code Interpreter)
    Quick GRBL setup guide for Windows (Arduino G-Code Interpreter)
  • Opensource CNC controller written for Arduino's (G-code interpreter GRBL)
    Opensource CNC controller written for Arduino's (G-code interpreter GRBL)
  • GRBL Arduino Library - Use the Arduino IDE to flash GRBL directly to your Arduino
    GRBL Arduino Library - Use the Arduino IDE to flash GRBL directly to your Arduino
  • Grbl (Arduino G-Code Processor) - Pin Layout
    Grbl (Arduino G-Code Processor) - Pin Layout
  • Raspberry Pi CNC Board / Hat
    Raspberry Pi CNC Board / Hat
  • Configuring Grbl (Arduino Based CNC-Controller)
    Configuring Grbl (Arduino Based CNC-Controller)
  • Arduino CNC - GRBL Shields / Boards
    Arduino CNC - GRBL Shields / Boards
  • GRBL Arduino Library
    GRBL Arduino Library

RSS Feed RSS - Posts

Categories

Archives

Subscribe to Blog via Email

Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 113 other subscribers

Tags

3d Printed 3d Printer 3d printing Arduino Arduino CNC Shield Arduino Shield ARM Automation BeagleBone CNC Delta Printer DIY Drone Feeds Foam grbl Hexapod Kicad Kickstarter Kossel Pro Laser cutter Lego Linux Milling Machine Openbeam Openhardware PCB Pick and place Pinout Pololu Power Supply Python Quadcopter Raspberry Pi Reprap Robot Robot Arm Robot of the week Robots Rostock Scara Shield Sketchup Stepper Driver Stepper Motors
© Copyright 2015 - Protoneer.co.nz
Infinity Theme by DesignCoral / WordPress