Slicer has problems with STL-files in ASCII-Format

Xmike · 2017-01-14 22:02:30

Since I've figured out how to adjust the print size in Autodesk Print-Studio, it has become my favorite program to generate supports.
However, the built-in slicer in Nanodlp has problems with STL files in ASCII format from Print-Studio.
STL files in binary format do not appear to be affected.

This is the Model:

Here is a layer pass through of the STL-file in ascii-format,
the first two layers are completely empty:

Here is a layer pass through of the STL-file in binary-format:

Last edited by Xmike (2017-01-14 22:08:04)

Shahin · 2017-01-15 07:28:23

Mike,

Open ASCII STL file with notepad++ or similar program, it is pretty easy to read source file. Make sure there is no empty layers at the beginning.

Xmike · 2017-01-15 13:04:53

If i do it with Asiga Stomp and Asiga Sleece, it seems to be a correct STL-ASCII-File.
File:
Printstudio_ASCII.zip

Shahin · 2017-01-15 20:40:20

I have found the cause of the issue. Please, try the beta version and let me know if the issue still persist.

Xmike · 2017-01-16 20:28:15

I get an error with ascii-Format as well as bin-format

Shahin · 2017-01-16 22:01:44

Mike,
Are you sure you have not filled rpi's SD card capacity? I have tried your source file plus couple of more with any issue today.

Xmike · 2017-01-17 19:00:31

I still get an error when importing the STL file with build 1329.
I have then reinstalled build 1323, and here is the import without error, but with the already mentioned layers.
(By the way, I always using the same file)
Build 1329

Last edited by Xmike (2017-01-17 19:05:40)

Shahin · 2017-01-17 19:05:32

What is your Z resolution? First you receive error http://www.nanodlp.com/forum/uploads/0f … a55f08.jpg and next during print you receive this one? http://www.nanodlp.com/forum/uploads/16 … fe6390.png

Xmike · 2017-01-17 19:11:30

The Z resolution was 0.1 mm each time.
Why the first error message came at the first layer, I can unfortunately no longer understand.
According to Asiga Sleece, there are 130 layers.

Xmike · 2017-01-17 19:22:50

NanoDLP takes 154 layers instead of 130 layers.

Last edited by Xmike (2017-01-17 19:23:04)

Shahin · 2017-01-18 05:14:14

Please, give the latest beta version another try.

Xmike · 2017-01-18 20:16:35

Everything now seems to be perfect.
The only thing that irritates me a bit is this message:

Shahin · 2017-01-18 20:25:33

It is fine, the message is not realtime. So if you have opened the panel before completion of slicing you will see this message.

nanoDLP

#1 2017-01-14 22:02:30

Slicer has problems with STL-files in ASCII-Format

#2 2017-01-15 07:28:23

Re: Slicer has problems with STL-files in ASCII-Format

#3 2017-01-15 13:04:53

Re: Slicer has problems with STL-files in ASCII-Format

#4 2017-01-15 20:40:20

Re: Slicer has problems with STL-files in ASCII-Format

#5 2017-01-16 20:28:15

Re: Slicer has problems with STL-files in ASCII-Format

#6 2017-01-16 22:01:44

Re: Slicer has problems with STL-files in ASCII-Format

#7 2017-01-17 19:00:31

Re: Slicer has problems with STL-files in ASCII-Format

#8 2017-01-17 19:05:32

Re: Slicer has problems with STL-files in ASCII-Format

#9 2017-01-17 19:11:30

Re: Slicer has problems with STL-files in ASCII-Format

#10 2017-01-17 19:22:50

Re: Slicer has problems with STL-files in ASCII-Format

#11 2017-01-18 05:14:14

Re: Slicer has problems with STL-files in ASCII-Format

#12 2017-01-18 20:16:35

Re: Slicer has problems with STL-files in ASCII-Format

#13 2017-01-18 20:25:33

Re: Slicer has problems with STL-files in ASCII-Format

Board footer