nanoDLP

Direct control with Rasp + applied motion driver

printer.mem

2017-06-03 07:39:15.808 {"Layer":"2","module":"Hardware","level":"Notice","msg":"Initializing build # 1465 - generic"}
2017-06-03 07:39:15.857748 {"Layer":"2","module":"Hardware","level":"Debug","msg":"Stepper motor enabled"}
2017-06-03 07:39:15.858013 {"Layer":"2","module":"Shutter","level":"Debug","msg":"Shutter Close"}
2017-06-03 07:39:15.858048 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving to top"}
2017-06-03 07:39:15.858199 {"Layer":"2","module":"Terminal","level":"Notice","msg":"Terminal Reader Activated"}
2017-06-03 07:39:15.858307 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving Up 100000000 pulses 100000 mm"}
2017-06-03 07:39:15.858453 {"Layer":"2","module":"GPIO","level":"Notice","msg":"Limit has been touched"}
2017-06-03 07:39:15.858615 {"Layer":"2","module":"Pulsing","level":"Warning","msg":"Limit touched position reset"}
2017-06-03 07:39:15.858768 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Movement Finished Pulse  0 / 100000000 ; Height  6000 / 0 ; Time 0.000310098"}
2017-06-03 07:39:15.858848 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving to Stop Position"}
2017-06-03 07:39:15.858932 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving Down 6000 pulses 6 mm"}
2017-06-03 07:39:16.010105 {"Layer":"2","module":"WIFI","level":"Warning","msg":"WIFI interface wlan0 detected"}
2017-06-03 07:39:16.022457 {"Layer":"2","module":"WiFi","level":"Debug","msg":"Status Monitoring"}
2017-06-03 07:39:16.078338 {"Layer":"2","module":"WIFI","level":"Warning","msg":"Connecting to FFff0987"}
2017-06-03 07:39:19.030341 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Movement Finished Pulse  6000 / 6000 ; Height  0 / 6000 ; Time 3.171171042"}
2017-06-03 07:39:26.023126 {"Layer":"2","module":"WiFi","level":"Debug","msg":"Connected to FFff0987"}

Last edited by 1125lbs (2017-06-03 07:45:03)

there's no movement, reboot the babe, the log says its done with routine put physicaly nothing changes,

I just come to lab ( did not turned the machine down) and see on trello board that you havve update pre -calculated pulse length so i just update it,

then the "buildhead" stay parked on 6mm waiting position, after update  its showing on calib. page that its currently on 0000000 position but its not, so no movement was done after upgrade

Issue Fixed !

thank you very much!

Hello fellows,

For shure,

Currently my setup is running with direct drive ( Applied Motion STR8 driver ), on early versions i had experiencing some cogging effect, maybe influenced for step emulation ( 20.000 steps / rev) which affect some velocity issues, them i had to stepdown this emulation and change velocities.

today i updated to Build 1537 and turn the drive to max emulation (20000steps/rev) and its running flowsly.

just to ensure i measure it with digital dial 0,001mm

one more time i would like to thank you for the impeccable work and to enable us to drive our machines with this greatest tool!

Last edited by 1125lbs (2017-06-21 17:55:22)