You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2017-10-15 10:23:04
- Hotam
- Member
- Registered: 2017-07-24
- Posts: 11
cant find the nanoDLP after slicing
hey there
so i sent an heavy STL to the nano DLP, what happend next is:
nanoDLP stop responding and disappeared from network -----> i restarted the RPi3 -----> now i cant find the nano DLP on my network 
(
is there any way to fix it? or i need to burn the image from scratch and loose all my resin profiles (( ?
Offline
#2 2017-10-15 21:45:41
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 1,834
Re: cant find the nanoDLP after slicing
SSH or SFTP into rpi and remove last plate on folder below.
/home/pi/printer/public/plates/
Offline
#3 2017-10-16 09:06:48
- Hotam
- Member
- Registered: 2017-07-24
- Posts: 11
Re: cant find the nanoDLP after slicing
10q very much 
y did that happen? is there some limitations in using the slicer?
Offline
#4 2017-10-16 14:20:33
- Hotam
- Member
- Registered: 2017-07-24
- Posts: 11
Re: cant find the nanoDLP after slicing
UPDATE: the nano DLP getting stuck now even with the simplest cube stl file...
would burning the image again fix this?
its making like 8 layers
and then stuck with:
9.png.tmp
10.png.tmp
Last edited by Hotam (2017-10-16 14:21:43)
Offline
#5 2017-10-16 18:44:44
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 1,834
Re: cant find the nanoDLP after slicing
Share debug file (setup page, tools tab, debug button). It should be fixable without rewriting SD image.
Offline
#6 2017-10-17 07:18:04
- Hotam
- Member
- Registered: 2017-07-24
- Posts: 11
Re: cant find the nanoDLP after slicing
10x for your help shahin
Offline
#7 2017-10-18 04:22:44
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 1,834
Re: cant find the nanoDLP after slicing
Have you removed plate? I do not see much log on debug file. Could you let it works for couple of minutes and take debug file as soon as you suspect it is going to get stuck.
Offline
#8 2017-10-18 07:33:42
- Hotam
- Member
- Registered: 2017-07-24
- Posts: 11
Re: cant find the nanoDLP after slicing
mmmmm yeah i removed the plate in order to be up and running with the nanoDLP
ill try to give more details:
im trying to slice an STL file, then everything is getting stuck and the nanoDLP goes offline no matter how much im waiting, i cant get in to the nanoDLP through the browser, and it disappear from the network, even after a reboot of the pi
so i use winSCP to look inside the raspberry, and i see the slicing got stuck after 8 layers.
then i use putty to delete the new plate folder
then i reboot the pi
and now the pi is back in the network and i can access it through the browser
BUT
now if i go to the plates, through the browser interface, i can see the plate i just deleted with the putty, and i can see the number of layers it should have, but if ill try to run it, it wont work.
and if ill go inside the pi through the winSCP, that plate does not exist... so i go back to the browser and delete the plate from the interface...
Offline
#9 2017-10-18 18:37:04
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 1,834
Re: cant find the nanoDLP after slicing
This is correct behavior as you have removed plate from disk but not from UI.
So after removing from UI still do you experience any issue? I mean still freezes on new plate uploads?
Offline
#10 2017-10-19 04:20:20
- Hotam
- Member
- Registered: 2017-07-24
- Posts: 11
Re: cant find the nanoDLP after slicing
yeah it still freeze
i formatted yesterday and burned a new image and now all is good...
Offline
Pages: 1