Air hockey robot EVO
The Air Hockey Robot EVO is finally here! A challenging robot, perfect to have fun and learn robotics at the same time
Controlled by your own smartphone using the free AIR HOCKEY ROBOT APP
This is a mostly 3D printable air hockey playing robot that, in addition to moving across the required two dimensions, can predict the movements of rebounding pucks and attack/defend in consequence.
CUSTOMISE YOUR AIR HOCKEY ROBOT EVO KIT:
Arduino LEONARDO (clone) + USB cable
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 . It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
The ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Leonardo to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port.
Details:
| Microcontroller | ATmega32u4 |
| Operating Voltage | 5V |
| Input Voltage (recommended) | 7-12V |
| Input Voltage (limits) | 6-20V |
| Digital I/O Pins | 20 |
| PWM Channels | 7 |
| Analog Input Channels | 12 |
| DC Current per I/O Pin | 40 mA |
| DC Current for 3.3V Pin | 50 mA |
| Flash Memory | 32 KB (ATmega32u4) of which 4 KB used by bootloader |
| SRAM | 2.5 KB (ATmega32u4) |
| EEPROM | 1 KB (ATmega32u4) |
| Clock Speed | 16 MHz |
| Length | 68.6 mm |
| Width | 53.3 mm |
| Weight | 20g |
B-robot 3 Axis Gyroscope + Accelerometer Module
The InvenSense MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel. Therefor it captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with the Arduino.
The MPU-6050 combines both an accelerometer and a gyro.
Details:
The power supply: 3-5 v (internal low voltage difference voltage stabilizing)
Communication: standard IIC communication agreement
Chip built-in 16 bit AD converter, 16 bits of data output
The gyroscope range: + 250 500 1000 2000 ° / s
Acceleration range: ± 2 ± 4 ± 8 ± 16 g
B-Robot EVO KIT (Plug and Play Robot version)
JJrobots´s B-ROBOT EVO 2 Kit. Created to simplify the set up and integration of all the different devices involved in this project.
This COMPLETE VERSION includes all the electronic and hardware components required to create the B-Robot. You just need to assemble everything (optional 3D parts)
What you get when you buy this KIT:
- jjRobots Brain Shield
- Arduino Leonardo (CLONE) + USB cable (already programmed)
- 2x High Quality NEMA17 stepper motors +14 cms cables (pair)
- 2x Stepper motor driver
- IMU (gyro+accelerometers) + custom cable
- Optional: 3D printed parts (vibrant colours)
- Powerful servo: Metal gears (you will need an arm to fight and raise your B-robot…)
- 6x AA Battery case with ON/OFF Switch (batteries not included)
- Bolts+nuts needed to set everything up
- Pair of nylon bumpers
- Double side tape, googly eyes…
- NEW: control your B-robot using the JJrobots FREE APP! (Android devices) or the Roverbot APP (for iOS phones. not official)
CUSTOMISE YOUR ROBOT:
iBoardbot. The internet controlled whiteboard robot
The iBoardbot is a robot connected to the internet capable of writing texts and drawing with great precision. Also, it can erase in a quick and effective way. Send to your iBoardbot your information from any part of the world. As it has a multi-user interface you can also play and challenge your kids, use it as a collaborative notice board or as a twitter wall in your shop window.
Take a look to a LIVE DEMO of the iBoardbot control WebApp here*
*The above WebApp link does not belong to any real iBoarbot. Play with it as much as you want
Features:
- Drawing mode: It can precisely draw what you assign to it. Different users will be able to collaborate with the drawing at the same time from different devices and world places. No matter how far the drawer is; the drawing precision will be as if the drawer himself was holding the pen with his hands
- Graphics mode: Upload and draw your own graphics using the iBoardbot´s webAPP!
- Text mode: Send any text. The iBoardbot will adjust it to the right size so it can fit on the board and it will draw it using its own font. Just type it and click/tap on SEND
- IFTTT integrated: Why not send the subject of an email you just have received to the iBoardbot? Or use the iBoardbot as a Twitter wall? Or write the last SMS you have got? Or display the temperature of your home? the weather forecast maybe? The last tweet from your favourite music band? or… there are as many possibilities as possible recipes. Create your own recipe!
The iBoardbot KIT
The kit is easy to assemble in an hour or so, and only requires a couple of basic tools like screwdrivers plus internet access to control the iBoardbot
The KIT includes:
All you need to create your own IBoardbot. Just follow the assembly instructions in order to set it up (the glass of your choice can be added to the KIT as an option.See below). With this KIT you won´t have problems getting the right cables, power supply, belts, bushings, bolts…It is just assembling
- GT2 timing belt (two segments of 53+100 cms)
- pulley gt2 20 tooth
- 608 bearing
- 623 bearing
- Stainless steel round bar (8mmØ,450mm length)
- 2x round anodised aluminium tube (6mmØ, 205 mm length)
- 4x 30 cms servo cable extender
- 2x 1.8deg HIGH QUALITY NEMA 17 Stepper motors (40mm length) (4.4Kg/cm torque)
- Motor cables (14+70 cms length do the job)
- 2x SG90 servo
- Arduino Leonardo compatible
- jjRobots Brain Shield
- 2x A4988 Stepper motor drivers
- Power supply 12v/2A
- 2x copper bushing (8x11×22)
- 6mm M3 bolts
- 16mm M3 bolts
- M3 nuts
- 1x M3 self locking nuts
OTHERS:
- 3mm wide/100mm long zip ties (~x10)
- 5mmØ cable wrap (~90 cms)
- 1x Staedtler MARKER (black)
- iBOARDBOT CLOUD SERVICE INCLUDED
iBoardbot. The internet controlled whiteboard robot. PLUG & PLAY VERSION
The iBoardbot is a robot connected to the internet capable of writing texts and drawing with great precision. Also, it can erase in a quick and effective way. Send to your iBoardbot your information from any part of the world. As it has a multi-user interface you can also play and challenge your kids, use it as a collaborative notice board or as a twitter wall in your shop window.
Customers reviews:
Features:
- Drawing mode: It can precisely draw what you assign to it. Different users will be able to collaborate with the drawing at the same time from different devices and world places. No matter how far the drawer is; the drawing precision will be as if the drawer himself was holding the pen with his hands
- Graphics mode: Upload and draw your own graphics using the iBoardbot´s webAPP!
- Text mode: Send any text. The iBoardbot will adjust it to the right size so it can fit on the board and it will draw it using its own font. Just type it and click/tap on SEND
- IFTTT integrated: Why not send the subject of an email you just have received to the iBoardbot? Or use the iBoardbot as a Twitter wall? Or write the last SMS you have got? Or display the temperature of your home? the weather forecast maybe? The last tweet from your favourite music band? or… there are as many possibilities as possible recipes. Create your own recipe!
The “Plug & Play” PREMIUM KIT has been assembled using:
- GT2 timing belt (two segments of 53+100 cms)
- pulley gt2 20 tooth
- 608 bearing
- 623 bearing
- Stainless steel round bar (8mmØ,450mm length)
- 2x round anodised aluminium tube (6mmØ, 205 mm length)
- 4x 30 cms servo cable extender
- 2x 1.8deg HIGH QUALITY NEMA 17 Stepper motors (40mm length) (4.4Kg/cm torque)
- Motor cables (14+70 cms length do the job)
- 2x SG90 servo
- Arduino Leonardo compatible
- jjRobots Brain Shield
- 2x A4988 Stepper motor drivers
- Power supply 12v/2A
- 2x copper bushing (8x11×22)
- 6mm M3 bolts
- 16mm M3 bolts
- M3 nuts
- 1x M3 self locking nuts
OTHERS:
- 3mm wide/100mm long zip ties (~x10)
- 5mmØ cable wrap (~90 cms)
- 1x Staedtler MARKER (black)
- iBOARDBOT CLOUD SERVICE subscription INCLUDED
jjRobots electronic brain shield v3.0 (Devia)
JJrobots´s Brain SHIELD. Created to simplify the set up and integration of all the different devices involved in the jjrobots projects.
This SHIELD has:
- TWO stepper motor OUTPUTs
- TWO SERVO OUTPUTs
- I2C communications
- Push button (customisable)
- SENSOR port (SONAR, IR…)
- ESP12-E (ESP8266) WIFI module (you can communicate to this SHIELD from any smartphone/tablet/PC using it)
Some OPEN robots you can create with this Brain Shield:
- B-ROBOT EVO is a remotely controlled self-balancing arduino robot created with 3D printed parts. With only two wheels, B-ROBOT is able to maintain his balance all the time by using his internal sensors and driving the motors. You can control your Robot, making him moving or spinning, by sending command through a Smartphone, Tablet or PC while he keeps the balance.
- The iBoardbot is an internet controlled robot capable of writing+drawing (and wiping!) on a glass surface.
- Remotely controlled Torch/ Laser robot: Laser pointer is a remotely controlled Arduino robot created with 3D printed parts. With only two servos, this robot is able to point any object in the X and Y axis.
- Sphere-O-Bot: The Sphere-O-bot is a friendly art robot that can draw on spherical or egg-shaped objects from the size of a ping pong ball to a large duck egg (4-9 cm).
- Many more to come!
NOTE: There are FULL ROBOT KITS ready to be sent to you in the SHOP (scroll down to the very end of this page to see them too)
NEMA 17 Stepper motor (PACK OF TWO) + CUSTOM CABLES
This is the motor used in every jjRobot. You liked the motors that came with your kit and want another pack of two? Do you like its sturdiness and its connector (forget to solder every time you have to change the cable length) ? This is the perfect stepper motor for MAKERs and Robots enthusiasts.
Select the cable you want with each motor for free!
SPECIFICATIONS
| Manufacturer Part Number | MT-1703HS168A |
| Step Angle | 1.8° |
| Step Accuracy | <5% |
| Holding Torque | 45 N·cm (62oz.in) |
| Rated Current/phase | 1.68A |
| Phase Resistance | 1.65ohms |
| Voltage | 12-24 V |
| Inductance | 3.6mH±20%(1KHz) |
| Weight | 280g |
Remotely controlled torch
This is a remotely controlled torch pointer (can be changed for a Laser pointer). Can be moved from your smartphone using the JJrobots FREE app available in Google Play or using OSCtouch (or equivalent OSC software).
NEW: control your robot using the FREE JJrobots google APP (android devices)!
- maximum range: up to 50-60 meters.
- It is portable if you use a small 7-9volts battery (Lipo/Alkaline/…) Drive your neighbour´s cat crazy from a distance by placing the robot on the roof! >:-)
This KIT includes:
- jjRobots Electronic Brain Shield 3.0
- Arduino Leonardo (compatible) + USB cable
- Battery connector (make it portable!)
- 2x Servos
Optional:
- 3D parts + CASE + bolts
- Torch (batteries included)
Stepper motor DRIVER (A4988) + heatsink
A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil. Here are some of the driver’s key features:
- Simple step and direction control interface
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- Heat sink included
This product ships with all surface-mount components—including the A4988 driver IC—installed as shown in the product picture.
This product ships individually packaged with 0.1″ male header pins included soldered in.
The most AWESOME robotics KIT
The robotic KIT you were looking for (and you didn´t know). Create very different OPEN SOURCE robots using the same electronics and ancillary elements. Everything can be modified, Hacked and customised!
Fight battles with your remotely controlled B-robot, play with your torch from 50 meters away, send messages to your friend using the Iboardbot!, paint balls/eggs using your own pens or…create your new awesome robot from scratch!
Do you think you can improve or hack any of these robots? Do it! They are OPEN SOURCE robots, so all the info,know how and code is available for everyone. Share the knowledge! (and take a look to the JJrobots FORUM)
The robots you can create from this KIT:
CUSTOMISE YOU AWESOME ROBOTICS KIT
The Sphere-O-bot painting robot
The Sphere-O-bot is a friendly art robot that can draw on spherical or egg-shaped objects from the size of a ping pong ball to a large duck egg (4-9 cm).
The robot is based on the original design of Evil Mad Scientist
Features:
The Sphere-O-Bot is a simple 2 axis drawing machine that can draw on most spherical surfaces. You can use it to decorate balls or eggs. This design also features the regular JJrobots electronics (the same we have used in all our robots). So you can create this robot or any other just simply printing new 3D printed parts and uploading the appropriate code.
The original idea belongs to Evil Mad Scientist
The frame was designed by Attila Nagy
The Sphere-O-bot is adjustable, and is designed to draw on all kinds of things that are normally “impossible” to print on. Not just eggs but ping pong balls, Christmas ornaments, light bulbs, and (yes) eggs (duck, goose, hens…).
The Sphere-O-bot frame was designed by Attila Nagy and slightly modified by JJrobots. The pen and egg motors are high-torque precision stepping motors, and the pen lift mechanism is a quiet and reliable servo (SG90) motor.
The Sphere-O-bot KIT
The KIT includes:
All you need to create your own Sphere-O-bot. Just follow the assembly instructions in order to set it up (the glass of your choice can be added to the KIT as an option.See below). With this KIT you won´t have problems getting the right cables, power supply, belts, bushes, bolts…It is just assembling
- 2x 623 ball bearings
- Threaded steel rod (3mmØ,80mm length)
- 1x compression spring (4,5mmØ, 10 mm length)
- 2x 1.8deg HIGH QUALITY NEMA 17 Stepper motors (40mm length) (4.4Kg/cm torque)
- Motor cables (14+70 cms long) (not in the photo)
- USB cable
- 1x SG90 servo
- Arduino Leonardo compatible
- B-robot Brain Shield
- 2x A4988 Stepper motor drivers
- Power supply 12v/2A
- 4x 6mm M3 bolts
- 14x 15mm M3 bolts
- 4x M3 nuts
- 2x 20mm Suction Cups
- 1x M3 wing nut
- 1x Marker PEN
