OSH Park
Profile for Cereal_Killer
- You need to sign in or sign up before continuing.
Shared projects
Ultimate LRS_Mini v1.01
by
Cereal_Killer.
2
layer board of
1.20x1.64
inches
(30.43x41.63
mm).
Shared on
July 10th, 2016 20:34.
v1.01 (this board supersedes v1.0)
NEW FOR VERSION 1:
-Improved silkscreen and labeling!
-Improved .sch!
-All silk readable w/o magnification!
-I’m still using a 4x4SMD tact button but now nearly any switch you can find will work with a little solder mask scraping!
-Provisions for >3S battery input!
If you want to run over 3S you have a new option- dont put the LM317 and it’s associated components on the board, instead use a UBEC (such as a Poloulu) and supply the board with 6V direct at the 2-pin input (upper right corner opposite antenna) and close the solder jumper on the right two legs of the LM317 (SJ1), when you do this STOP APPLYING POWER ON THE VIN PIN! DONT FORGET THIS STEP, YOU MUST REMOVE POWER INPUT FROM THE SIG/VIN/GND CONNECTOR! This will run the entire board (including arduino & Hope RF module) at 6v from any voltage your chosen UBEC can accept. (If you dont close the jumper the arduino will continue to receive it’s RAW power from the main source then you can use your own voltage supply for the Hope RF module, effectively making it run at any power level you wish. This also makes it easier for people who dont want to source LM317’s and have other LDO’s laying around). This method provides easy provisions for two groups of users, those wanting to independently supply the voltage to the Hope RF modue (either cause they have another type of Vreg and dont want to buy LM317’s or maybe because they want to adjust the power output on demand), it will also provide a easy way to run it on higher voltage systems (the reason I needed it)
All 0805 size components (including LEDs). All component values are marked on the silkscreen except for C4 and C5, please decide if you want to use them and choose appropriate values based off the datasheet
Project links:
ATTN: You MUST file / sand the edges of the Arduino mini down so they essentially become board edge vias. Dont worry, this process is very simple and makes very clean looking edge connections that are very easy to solder with very minimal work. Quickly sand / file the board edges down about 2/5 of the way threw the vias.
Note In the project thread on RCGroups I have pictured of built boards I’ve completed using a very strange Arduino Pro Mini clone with a double row of pins at the bottom for SPI and A4-A7, please DO NOT BE CONCERNED that you cant find that specific arduino clone, the pins needed for Ultimate LRS mini are all 1-to-1 compatible with the standard Arduino Pro-Mini and all it’s exact clones. Pretty much any 328p mini board you find will work and ULRS is using the most common pins that are [even on boards with slight differences] always in the same spot!!
ULRS_Mini_CK v1.0
by
Cereal_Killer.
2
layer board of
1.20x1.64
inches
(30.43x41.63
mm).
Shared on
July 10th, 2016 19:49.
v1.0 (this board supersedes by v1.01. please click link to be taken there
https://oshpark.com/shared_projects/2nCtZIbE
Full Naze32 Tricopter expansion board
by
Cereal_Killer.
2
layer board of
1.89x1.86
inches
(48.11x47.12
mm).
Shared on
August 11th, 2015 21:06.
DO NOT ORDER, NOT READY, DOES NOT WORK!
CK's MPU6050 Breakout
by
Cereal_Killer.
2
layer board of
1.01x0.61
inches
(25.65x15.49
mm).
Shared on
June 15th, 2015 16:23.
Use these boards to recycle the MPU6050 gyro off your old / broken flight controllers. I pull them off broken toy grade all-in-one integrated controllers mostly. In the end you only save a few bucks but I hate seeing good parts go in the bin cause I dont have use for the board as a whole.
Note this is a 3v3 board only, DO NOT apply 5V or you WILL kill the gyro, it’s a 3.6v max iC and the common GY-521 breakout has an on board regulator, again this one DOES NOT and only takes 3.3V in! This is prrety much the sparkfun board but with the addition of a indicator LED.
Please see pic’s and description in my RCGroup Blog Post below: http://www.rcgroups.com/forums/showthread.php?t=2438079#post31901300
LED pull-up to turn off test board 061115
by
Cereal_Killer.
2
layer board of
0.53x0.64
inches
(13.54x16.23
mm).
Shared on
June 11th, 2015 19:01.
does exactly what it sais, nothing more, probably not useful to anyone else…