nanoDLP

Interestingly,
one raspberry, works perfectly  after adding to pi 8080
but the second raspberry does not want to work quickly
remotely connected to other computers---same result on video
video.rar

http://moemesto.ru/elshad666/files

the first one is set to 16 gb 10 class  Sandisk  ultra  --it works fine
and on the second 8 gb 10 class  (maybe just a falsh wrote 10) 
it possible that the SD is not the original,and therefore slows  ?

the settings on both are identical  1771
and the same settings on the Win versions  1769

HI Shahin

I set up a mask for raspberries and for win
rectangle 0.1 thickness in 4 layers to output to the projector
edited many times changed  mask intensity and click  recreate
win version of the slicing in a couple of seconds
but raspberry about 1 min  only 4 layers
every 5 seconds clicked update
windows is 8080
raspberries  80    IP  if write or leave blank ... no difference slicing  about 1 min
I do not know   maybe they all conflict
wiring diagram  all   IP  constants

http://moemesto.ru/elshad666/files

I still think that the created a zip file with only a png  this will be the fastest option

Thanks for your attention

these three printed in one place or in different?
build  plate calibrated horizontally with respect to the screen?

HI Shahin

I know, I checked but tests showed
there is no difference if the win is enabled or not

PC ip192.168.0.103  Constant  in the router
PI   ip192.168.0.101 Constant  in the router
in setup  in pi  TCP 80    in  TCP ip port  of slicer   enter 192.168.0.103 or leave empty  (did restart  ri )

I think that the remote slicer  not active
maybe I'm not typing in correctly ? I only write  192.168.0.103,,how right?
or something else that needs to be configured in the router?
or something else that needs to be set up in the PC   WIN 7 64?

Thank you for your attention,
I checked the new version,,1769
if someone does not need a color he may not use
please look at the screenshots here
http://moemesto.ru/elshad666/files

I think that setting the lamp clock will not work properly,,I have been using for 3 years  ACER 1500  and ACER 6510
And every time I check the lamp clock, readings are different and do not correspond to reality
for example yesterday was 800 today 1200,,so I do not believe the data,,I correct the mask every 2 weeks

teşekkürler

NEXT
405nm color corresponds to RGB 73,0,188 ..if inserted in Mask Generation ..Final Mask  gives out a dark gray
To check it is necessary to cut a flat model or pillar  and in settings  in Add Plate  in Decrease Mask Intensity  100
and  open  layers  >>display layers  and and measure with   uv a sensor  ,,sensor measurement does not correspond to,my settings mask

I have the same problem
how to put it right
/home/pi/printer/db/machine.json  in  putty  ?

pi@nanodlp:~ $ /home/pi/printer/db/machine.json
-bash: /home/pi/printer/db/machine.json: Permission denied
pi@nanodlp:~ $

what is not correctly written?
How can I put it right?

found

sudo nano /home/pi/printer/db/machine.json

try swapping
outputs on the video card
I had a problem on the xp
and check the card supports open GL it should be minimum 2.1

HI Shahin

still found that

if  gray ''nanodlp  image viewer" and calibration  not works
click start print and click  ''nanodlp  image viewer" ,it changes its color to white
and the image  layers goes to the projector,if  click on any part of the monitor, it changes its color to gray
and images layers do not go to the projector  ,,''nanodlp  image viewer" it works as an on / off switch

thank you very much for your attention
Elshad

HI Shahin

maybe that I caught the virus and it all messed up
Can tell me where to get an older versions of nanodlp for Windows. I couldn't find it anywhere

thank you very much for your attention
Elshad

uploaded to my file exchanger

http://moemesto.ru/elshad666/files

still such a question , there are two the same pi ,on one 8GB ,on another 16 GB, both empty,
on that where 16, always writes
Free space available on your disk is low. Please remove some plates.
and on the other never, it was not written
16GB actually tested 14.8
as it is understood, if there is more
or as  can increase this memory

thank you very much for your attention

Elshad

maybe it will help
after  ########################   down I added for the projector,,you deleted

and delete ## this for lcd

# Wanhao D7 nanodlp config
# V1.0 3-feb-2017

# CAMERA SETTINGS ( 1 = ON, 0 = OFF)
#start_x=1
disable_camera_led=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

##//hdmi_timings=<h_active_pixels> <h_sync_polarity <h_front_porch> <h_sync_pulse> <h_back_porch> <v_active_lines> <v_sync_polarity> <v_front_porch> <v_sync_pulse> <v_back_porch> <v_sync_offset_a> <v_sync_offset_b> <pixel_rep> <frame_rate> <interlaced> <pixel_freq> <aspect_ratio>

# DISPLAY SETTINGS
##gpu_mem=192
##hdmi_force_hotplug=1
##hdmi_timings=1440 0 50 10 35 2560 0 4 2 2 0 0 0 50 0 198000000 0
##hdmi_group=2
##hdmi_mode=87
##hdmi_pixel_freq_limit=500000000
##hvs_priority=0x32ff
##display_rotate=0x10000
##max_framebuffer_width=1440
##max_framebuffer_height=2560
##framebuffer_width=1440
##framebuffer_height=2560
##framebuffer_depth=24
##framebuffer_ignore_alpha=1
##config_hdmi_boost=2
##dtparam=i2c_arm=on6

######################################################

hdmi_pixel_encoding=2

start_x=1
gpu_mem=128

disable_camera_led=1
dtparam=i2c1=on
dtparam=i2c_arm=on
disable_overscan= 1